Posted   by 

Zte Gpon Snmp Management

ZTE GPON OLT SNMP Server Configure

Today i will discuss how to ZTE GPON OLT SNMP Server Configure in ZXA10 C220 & C300 series OLT.

ZTE GPON OLT SNMP Server Configure Example ZXAN(config)#snmp-server community public view allview ro ZXAN(config)#snmp-server enable trap ZXAN(config)#snmp-server host 10.62.31.123 trap version 2c pulic enable NOTIFICATIONS server-index 1. Zte F670L Admin Password: Zte Gpon Olt Snmp Server Configure Example: Try logging into your zte router using the username and password. Factory default settings for the zte all models wireless router. Not to control dhcp mode. Below is list of all the username and password combinations that we are aware of for zte routers. Merely said, the zte gpon is universally compatible with any devices to read OLT ZTE C300 CONFIG THE ONU HUAWEI FIBERHOME ZTE. CLI V2.1 CLI OLT C320 REGISTER ZTE ONU ZTE GPON SNMP management 2016 New GPON OLT configure Internet service on the ZTE SFU ZTE GPON OLT configure multicast service on the Realtek HGU ZTE C320 GPON.

Prerequisites:

  • Make sure that the network device works normally.
  • Log in to the ZXA10 C220 through HyperTerminal or Telnet.

Context: SNMPis essentially a request-reply protocol running over UDP
(ports 161 and 162), though TCP operation is possible. SNMP is
an asymmetric protocol, operating between a management station and an agent. The agent is the device being managed – all its software has to do is implement a few simple packet types and a generic get-or-set function on its MIB variables. The management station presents the GUI by collecting MIB data over time.

The ZXA10 C220 supports SNMP v1/v2/v3.

To configure the SNMP server, perform the following steps:

Step-1: Use the configure terminal command to enter global configuration mode.

Step-2: Use the snmp-server community command to configure SNMP community.

Step-3: Use the snmp-server location command to configure physical location information.

Step-4: Use the snmp-server enable command to configure trap type.

Note: Trap is the unsolicited information which is sent to the NMS by a managed device . It is used to report urgent events. The ZXA10 C220 supports six types of traps: SNMP, BGP, OSPF, RMON, STALARM, and VPN.

Step-5: Use the snmp-server host command to configure SNMP server (trap destination host).

Step-6: Use the show snmp config command to query SNMP configuration.

ZTE GPON OLT SNMP Server Configure Example:

Configure SNMP server:

  • Community: Public
  • Right: Read only
  • SNMP server host: 10.62.31.123
  • SNMP version: v2

ZXAN#configure terminal
Enter configuration commands, one per line. End with CTRL/Z.
ZXAN(config)#snmp-server community public view allview ro
ZXAN(config)#snmp-server enable trap
ZXAN(config)#snmp-server host 10.62.31.123 trap version 2c pulic enable NOTIFICATIONS server-index 1

Snmp Management Software

ZXAN(config)#show snmp config
snmp-server location xxxx, yyy, Bangaldesh.
snmp-server contact +88-017-xxxxxxxx
snmp-server packetSize 3000
snmp-server engine-id 830900020300010289d64401
snmp-server community public view allview rw
snmp-server view allview internet included
snmp-server view DefaultView system included
snmp-server host 10.62.31.123 trap version 2c pulic enable NOTIFICATIONS server-index 1 udp-port 162
snmp-server enable trap SNMP
snmp-server enable trap VPN
snmp-server enable trap BGP
snmp-server enable trap OSPF
snmp-server enable trap RMON
snmp-server enable trap STALAR

Details

WODAPLUG WDS111HZ 1*GE EPON ONU (1*10/100/1000Mbps) , ZTE Chip, PPOE support

Brief Views

EPON ONU WDS111HZ is designed mainly for FTTH ,FTTO application. EPON ONU FD111HZ support 1000Base-PX20+ standard with 1:64 maximum optical splitting ratio and 20km distance, and provide 1uplink GE PON port.

ONU WDS111HZ together with OLT could realize flexible network structure and maintenance and provide total FTTx solutions.

ONU WDS111HZ has 1 PON port , WDS111HZ provide one GE auto-adapting Ethernet port - 1*10/1000 M BASE-T port, Based on famou ZTE chip and PPOE support ! .

Passive Optical Network ( PON , Passive Optical Network ) consists of an optical line termination ( Optical Line Termination , OLT) at the central side of the network to which is attached a branched structure of optical splitters – splitters . These are connected end optical network unit ( Optical Network Unit , ONU ), most often in a tree , or ring or star topologies . The distance between the OLT and ONU can be up to 20 km .

Optical netwok behave transparently as smart switch, VLAN can be configured for each port of end ONU units. Configuration of ONU is easy thanks to preconfigured templates ( 4 and 8 ports OLT units has template management in base version ! ! ) Newly connected ONU unit automaticly downloads configuration from previosely set template (provisioning). Configuration OLT unit is possible 1. thru supplied EMS configuration software – central management ) based on SNMP (needs mySQL and reqiure additional SW instalation on master managing PC) or 2. by telnet and CLI (standard command line interface). Wodaplug units supports SNMP (mibs) protocol.

FD111HZ is based on ZTE high-performance xPON access chip. The chip supposes three mode：EPON/EPON/P2P, comply with the EPON standard of g.984, g.983, 802.3-2005, CTC EPON equipment technical requirements, have good xPON interoperability compatibility

FD111HZ provide one GE auto-adapting Ethernet ports. The FD111HZ features high-performance forwarding capabilities to ensure excellent experience with Internet and HD video services. Therefore, the FD111HZ provides a perfect terminal solution and future-oriented service supporting capabilities for FTTH deployment. It has good third-party compatibility to work with the third party OLT, such as Huawei/ZTE/Fiberhome/Alcatel-Lucen.

Features

n Full compatible with IEEE802.3ah

Zte Gpon Snmp Management Software

n Support port-based rate limitation and bandwidth control

n In compliant with IEEE802.3ah Standard

n Up to 20KM transmission Distance

n Support data encryption, group broadcasting, port Vlan separation , etc.

n Support Dynamic Bandwidth Allocation (DBA)

n Support ONU auto-discovery/Link detection/remote upgrade of software;

n Support VLAN division and user separation to avoid broadcast storm;

n Support power-off alarm function ,easy for link problem detection

n Support broadcasting storm resistance function

n Support port isolation between different ports

n Support three layer routing functions

n Support ACL and SNMP to configure data packet filter flexibly

n Specialized design for system breakdown prevention to maintain stable system

n Support software online upgrading

Zte Gpon Snmp Management

n EMS network management based on SNMP ,convenient for maintenance

Environmental Parameter

= Environmental Requirement

Operation temperature：-0°C～50°C

Zte Gpon Snmp Management Software

Operation humidity：5%—95%

= Power Specification

Zte Gpon Snmp Management

Rate voltage/ current：12 V/0.5A

Power：<2W

Login ONU web

Set computer local IP address manually to 192.168.101.100, using network cable, connect the computer with EPON ONU Ethernet ports, open a browser, copy and paste the URL: http://192.168.101.1

- for more please read user guide - http://www.wodaplug.com/download/EPON/ONU/FD111HZ-1GE-EPON-ONU-UserManual.doc

Interface

Indicator light

Introduction

1

LAN

LAN port status

On: Ethernet connection is normal;

Blinking: Data is being transmitted through the Ethernet port;

Off: Ethernet connection is not set up;

2

LOS

EPON optical signals

On: Optical power lower than receiver

3

PON

ONT Register

On: Success to register to OLT;

Blinking: In process of registering to OLT;

Off: In process of registering to OLT;

4

PWR

Power status

On: The ONT is power on;

Off: The ONT is Power off;

Application